3
PM200CSD060
Intellimod™ Module
Three Phase IGBT Inverter Output
200 Amperes/600 Volts
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
Electrical and Mechanical Characteristics, T
j
= 25°C unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Units
Control Sector
Over Current Trip Level Inverter Part OC T
j
= -20°C——1010 Amperes
(V
D
= 15V) T
j
= 25°C 518 609 850 Amperes
T
j
= 125°C 310 — — Amperes
Short Circuit Trip Level Inverter Part SC -20°C ≤ T
j
≤ 125°C, V
D
= 15V — 560 — Amperes
Over Current Delay Time t
off(OC)
V
D
= 15V — 10 — µS
Over Temperature Protection (V
D
= 15V) OT Trip Level 111 118 125 °C
OT
R
Reset Level — 100 — °C
Supply Circuit Under Voltage Protection UV Trip Level 11.5 12.0 12.5 Volts
(-20 ≤ T
j
≤ 125°C) UV
R
Reset Level — 12.5 — Volts
Circuit Current I
D
V
D
= 15V, V
CIN
= 15V, V
N1
-V
NC
—4562mA
V
D
= 15V, V
CIN
= 15V, V
XP1
-V
XPC
—1520mA
Input ON Threshold Voltage V
CIN(on)
Applied between 1.2 1.5 1.8 Volts
Input OFF Threshold Voltage V
CIN(off)
U
P
, V
P
, W
P
, U
N
, V
N
, W
N
1.7 2.0 2.3 Volts
Fault Output Current* I
FO(H)
V
D
= 15V, V
FO
= 15V — — 0.01 mA
I
FO(L)
V
D
= 15V, V
FO
= 15V — 10 15 mA
Minimum Fault Output Pulse Width* t
FO
V
D
= 15V 1.0 1.8 — mS
*Fault output is given only when the internal OC, SC, OT and UV protections schemes of either upper or lower devide operate to protect it.
Thermal Characteristics
Characteristic Symbol Condition Min. Typ. Max. Units
Junction to Case Thermal Resistance R
th(j-c)Q
Each IGBT — — 0.21 °C/Watt
R
th(j-c)F
Each FWDi — — 0.35 °C/Watt
R
th(j-c´)Q
Each IGBT** — — 0.13
†
°C/Watt
R
th(j-c´)F
Each FWDi** — — 0.21
†
°C/Watt
Contact Thermal Resistance R
th(c-f)
Case to Fin Per Module, — — 0.018 °C/Watt
Thermal Grease Applied
** T
C
measured point is just under chip.
† If you use this value, R
th(f-a)
should be measured just under the chips.
Recommended Conditions for Use
Characteristic Symbol Condition Value Units
Supply Voltage V
CC
Applied across P-N Terminals 0 ~ 400 Volts
Control Supply Voltage*** V
D
Applied between V
UP1
-V
UPC
, 15 ± 1.5 Volts
V
N1
-V
NC
, V
VP1
-V
VPC
, V
WP1
-V
WPC
Input ON Voltage V
CIN(on)
Applied between 0 ~ 0.8 Volts
Input OFF Voltage V
CIN(off)
U
P
, V
P
, W
P
, U
N,
V
N,
W
N
4.0 ~ V
D
Volts
PWM Input Frequency f
PWM
Using Application Circuit 0 ~ 20 kHz
Minimum Dead Time t
DEAD
Input Signal ≥ 2.5 µS
*** With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak.
(9 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern